HSAF16 S IT
Article number: 30 501- Surge arresters type T3 with high-frequency filters for serial connection.
- Intended for protection of electronic appliances against the effects of switching, induced and residual overvoltage in insulated power supply systems.
- Contain an improved thermal fuse, which ensures timely disconnection of HSAF* S from the power grid during the MOV‘s overheating and thus prevents damage to the HSAF* S.
- Installed at the boundaries of LPZ 2 – LPZ 3, as close to the device to be protected as possible (no further than 5 m).
- In front of HSAF* S must be installed a lightning current and surge arrester T1 and T2 from HAKEL company.
- S indication specifies a version with remote monitoring.
| Test class according to EN 61643-11:2012 (IEC 61643-11:2011) | T3 | |
| System | IT | |
| Number of poles | 2 | |
| Rated operating AC voltage | UN | 230 V |
| Maximum continuous operating voltage AC | UC | 275 V |
| Rated load current | IL | 16 A |
| Open circuit voltage of the combination wave generator | UOC | 6 kV |
| Voltage protection level at UOC (L1/L2) | Up | < 1.4 kV |
| Voltage protection level at UOC (L1/PE, L2/PE) | Up | < 0.9 kV |
| Nominal discharge current for class II test (8/20) | In | 3 kA |
| Total discharge current (8/20) L1+L2->PE | ITotal | 6 kA |
| Asymmetrical attenuation of filter at f = 4 MHz | > 80 dB | |
| Asymmetrical attenuation of filter at f = 0.15 ÷ 30 MHz | > 35 dB | |
| Temporary overvoltage test (TOV) for tT = 5 s (L1/L2) | UT | 337 V |
| Temporary overvoltage test (TOV) for tT = 0.2 s (L1/PE, L2/PE) | UT | 1 455 V |
| Response time (L1/L2) | tA | < 25 ns |
| Response time (L1/PE, L2/PE) | tA | < 100 ns |
| Power dissipation | Pz | < 3.5 W |
| Maximal back-up fuse | 16 A gL/gG | |
| Lightning protection zone | LPZ 2-3, LPZ3 | |
| Housing material | Polyamid PA6, UL94 V-0 | |
| Degree of protection | IP20 | |
| Operating temperature | ϑ | - 40 ÷ 55 °C |
| Recommended cross-section of connected conductors | S | 2.5 mm2 |
| Clamp fastening range (solid conductor) | 0.2 ÷ 6 mm2 | |
| Clamp fastening range (stranded conductor) | 0.2 ÷ 4 mm2 | |
| Tightening moment | 1,2 | |
| Installation | On DIN rail 35 mm | |
| Modular width | 4 | |
| Operating position | Any | |
| Signalling at the device | Optic | |
| Importance of local signaling |
OK – red light off FAULT – red light on |
|
| Remote signalling | Yes | |
| Potential free signal contact (S) (recommended cross-section of remote monitoring max. 1 mm2) | AC: 250 V / 1.5 A, DC: 250 V / 0.1 A | |
| Includes EMI / EMC filter | Yes | |
| Modular design | No | |
| Lifetime | > 100 000 h |